Warning: Cannot modify header information - headers already sent by (output started at /websites/ou/ouroborosdesign.com/index.php:43) in /websites/ou/ouroborosdesign.com/wordpress/wp-includes/feed-rss2.php on line 8
Ouroboros design Architecture http://ouroborosdesign.com Great design and friendly service Thu, 28 Jun 2018 22:56:43 +0000 en-US hourly 1 59580803 Mr Fluffy block design process Pt2 http://ouroborosdesign.com/index.php/mr-fluffy-block-design-process-pt1-copy/ http://ouroborosdesign.com/index.php/mr-fluffy-block-design-process-pt1-copy/#respond Mon, 07 Aug 2017 22:20:42 +0000 http://ouroborosdesign.com/?p=255 Fig 1 Site plan subdivision Fig 1 Site plan subdivision This is the second post on how we go about designing a new dwelling on a Mr Fluffy block or an existing block where you want to add a second dwelling. At this stage we need to propose a line to split the block to […]

The post Mr Fluffy block design process Pt2 appeared first on Ouroboros design Architecture.

]]>
Site split R1

Fig 1 Site plan subdivision

Fig 1 Site plan subdivision

This is the second post on how we go about designing a new dwelling on a Mr Fluffy block or an existing block where you want to add a second dwelling.

At this stage we need to propose a line to split the block to do this we need to determine a split that gives us the desired plot ratios.

  1. 50% building to 50% land in some cases
  2. In this case 50% for the fron block and 35% for the rear block.

When considering the split we need to keep in mind that a 3 bedroom house with ensuite will be approx 120sqm + 18sqm for a garage. In this case we needed aprox 395 sqm.

This gives us a starting point for the next part in developing a suitable floor plan.

the ACTPLA site has more has more information and Mr fluffy blocks next auction registrations CIVIUM

In part 3 we will go through the next stage of design development in developing a suitable floor plan

The post Mr Fluffy block design process Pt2 appeared first on Ouroboros design Architecture.

]]>
http://ouroborosdesign.com/index.php/mr-fluffy-block-design-process-pt1-copy/feed/ 0 255
Mr Fluffy block design process Pt1 http://ouroborosdesign.com/index.php/mr-fluffy-block-design-process-pt1/ http://ouroborosdesign.com/index.php/mr-fluffy-block-design-process-pt1/#respond Sat, 29 Jul 2017 07:11:59 +0000 http://ouroborosdesign.com/?p=244 Fig 1 Site plan measured This will be the first post on how we go about designing a new dwelling on a Mr Fluffy block or an existing block where you want to add a second dwelling. The first step is to have a site survey completed by a registered surveyor ( we also need […]

The post Mr Fluffy block design process Pt1 appeared first on Ouroboros design Architecture.

]]>
Site plan start edit

Fig 1 Site plan measured

This will be the first post on how we go about designing a new dwelling on a Mr Fluffy block or an existing block where you want to add a second dwelling.

The first step is to have a site survey completed by a registered surveyor ( we also need to measure the sag on the any overhead lines and convert that information into a measured site plan.

At this stage and in this particular case there was an existing 2 story house already on the block so what else do we need to work out.

  1. Easements; we need to provide access to these and maintain clearance from the proposed new building.
  2. Northern boundary’s; we need to keep an eye on these as in the ACT there is a requirement to maintain solar access to the adjoining property.
  3. Trees; In the ACT trees are regulated when they reach a certain size it can be difficult to gain approvals to remove a regulated tree and the design need to be done to keep these where possible. (separate applications are required)
  4. Driveways; New driveway entry’s on the verge need to take the location of storm water pits and sight lines into account.(separate applications are required)
  5. Clearance to all boundary’s and building zones, generally you are allowed 1 zero boundary but this needs to be a non habitable room such as a garage.
  6. Plot ratios; Building areas need to be carefully worked out as this is a mandatory requirement and can be 50 or 35% of the split block this depends on a number of factors one of which is the width of street frontage. Their a number of ways to increase the allowable floor area through careful design and each will depend on all the constraints outlined so far.

the ACTPLA site has more has more information and Mr fluffy blocks next auction registrations CIVIUM

In part 2 we will go through the next stage of design development and propose a site split for the new dwelling

The post Mr Fluffy block design process Pt1 appeared first on Ouroboros design Architecture.

]]>
http://ouroborosdesign.com/index.php/mr-fluffy-block-design-process-pt1/feed/ 0 244
OURO FFF 3d printer early in the build process http://ouroborosdesign.com/index.php/ouro-fff-3d-printer-early-build-process/ http://ouroborosdesign.com/index.php/ouro-fff-3d-printer-early-build-process/#respond Fri, 20 May 2016 00:20:10 +0000 http://ouroborosdesign.com/?p=185 Some pictures of the early build of our 3d printer

The post OURO FFF 3d printer early in the build process appeared first on Ouroboros design Architecture.

]]>
Some pictures of the early build of our 3d printer

IMG_0767

IMG_0784

IMG_0786

The post OURO FFF 3d printer early in the build process appeared first on Ouroboros design Architecture.

]]>
http://ouroborosdesign.com/index.php/ouro-fff-3d-printer-early-build-process/feed/ 0 185